How To Change Pur Water Filter Dispenser

Download Commodity

PUR has multiple products available for filtering water, but the filters become less constructive over fourth dimension as they fill with contaminants. How y'all replace the filter depends on which system you're using. If you take a plastic pitcher or dispenser y'all keep in the fridge, soak the new filter earlier screwing it in. For filtration systems that adhere to your sink faucet, simply remove the old filter so you can put the new one in its identify. When you're finished, you lot'll have clean water to drink for another few months!

1
Soak the replacement filter in cold water for 15 minutes. Place the new filter in a clean container that'south deep enough then you can fully submerge information technology. Fill the container with cold water and leave it lonely for at least 15 minutes. During this fourth dimension, any excess carbon from the filter volition elevator out and separate so information technology doesn't get in your drinking h2o.^[1]
- Soaking the filter also ensures that water flows evenly when you use it.
- Don't utilize water warmer than 86 °F (30 °C) since it could damage the filter.
Warning: Avoid using third-political party filters with your PUR bullpen or dispenser since they may not fit also or have been tested as efficiently.
ii
Twist the former filter counterclockwise to remove it. Have the chapeau off of the bullpen or dispenser and gear up information technology aside. And so, elevator upward the cascade tray, which is the blue plastic reservoir on meridian, and accept information technology out. Grab the cylindrical filter from the lesser and rotate it counterclockwise so information technology unhooks from the filter. Pull the former filter out through the top of the pour tray and throw in the garbage.^[2]
- Await until the pour tray is empty to change your filter, or else it may be difficult to remove or yous may spill.
Advertising
3
Rinse the new filter under your faucet for 10 seconds. Accept the filter out of the container when information technology's finished soaking and hold information technology underneath your faucet. Plow on cold h2o and rotate the filter and so you can rinse it off completely. Subsequently x seconds, turn off the water and shake out any excess that's still in the filter.^[3]
- Don't employ hot water to rinse the filter off, or else yous may damage it.
four
Screw the filter clockwise into the pour tray to secure information technology. Slide the long, cylindrical office of the filter through the hole in the centre of the pour tray and push it down as far as it goes. Hold the filter by the bottom and rotate it clockwise until you hear it click into place. Try tapping on the terminate of the filter to make sure information technology doesn't pop out from the pour tray. Identify the pour tray back into the pitcher or dispenser earlier replacing the lid.^[4]
- If the filter does pop out of the pour tray, then you didn't properly secure it. Reinsert it and endeavor turning information technology clockwise again.
- PUR filters for pitchers and dispensers commonly work for 40 gallons (150 L), or approximately 2 months.
5
Hold the Reset button down for 5 seconds if your pitcher or dispenser has one. Some newer PUR pitchers and dispensers have sensors that observe when you need to replace the filter. Correct after you lot replace the filter, printing the Reset button on the lid and keep it held down for 5 seconds. A light-green lite will blink on the lid once the sensor resets.^[5]
- Older pitchers or dispensers may not have an electronic display.
Advertisement

one
Unscrew the filtration system from your faucet. Support the weight of the filtration arrangement with your nondominant hand so it doesn't fall and suspension. Rotate the plastic locking nut holding the filtration system to the faucet counterclockwise to loosen it. Once you unscrew the system completely, advisedly lift it away from the faucet and set it downward on a countertop or towel.^[6]
- Water may spill out from the faucet when you lot unscrew the filtration system.
- Some models of PUR filtration systems may snap onto the faucet. If it doesn't unscrew, try pulling it direct downwards from the faucet.
ii
Twist open the summit comprehend of the arrangement to remove the sometime filter. Concur the filtration organisation so the rounded cease of the large cylinder points up. Unscrew the height from the cylinder by rotating it counterclockwise, and prepare the cover bated. Pull the old filter straight out from the system and throw it away in your trash.^[7]
- The top encompass is ever on the contrary end of the spout that dispenses h2o.
3

Set the new filter inside of the system and screw on the cover. Make sure the narrower end of the filter is on the bottom and the logo is right-side upwardly. Identify the filter into the filtration organisation and then it has a loose fit. Fix the top cover back over the filter and screw it into place to secure information technology.^[8]
4
Reattach the filtration arrangement to your faucet. Hold the filtration system against the bottom of the faucet so the threadings are perfectly horizontal, or else they won't form a tight seal. Rotate the locking nut clockwise onto the faucet and keep tightening information technology until it'southward manus-tight. Turn on the water and make sure information technology doesn't drip or leak at the seam.^[9]
- If your filtration system doesn't screw on, line information technology upwards with the faucet and utilize house pressure to snap it on.
5
Run cold water through the filtration organization for five minutes. Turn the handle on the correct side of the filtration system to divert the water through the filter. Allow the h2o to run through the filter for 5 minutes to get rid of whatsoever residue inside and so it works more than efficiently. Subsequently that, you lot can employ the filter immediately subsequently turning it on.^[ten]
- PUR faucet filters work for 100 gallons (380 L) of water, or about iii months of use.
- Don't run water over 100 °F (38 °C) through the filter since you could damage it.
Warning: The h2o may sputter or look cloudy when you start use the new filter, but information technology will become better as you run h2o through information technology.

Advert

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertizement

Many PUR filtration systems have electronic lights that detect when you lot demand to change your filter. If you lot meet a green light wink, yous don't need to change your filter. If information technology blinks xanthous or ruby-red, then you need to replace the filter presently.^[xi]

Cheers for submitting a tip for review!

Advertising

Don't use h2o that's higher up 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since information technology can damage the filter.^[12]
Just use the filter with water that's already safe to drink since information technology will non remove leaner or infection.^[thirteen]

Advertising